Ergodyne Squids 3194 Hand Tool Tethering Kit
-
Qty total:0
-
Subtotal:$0.00
Item Attributes
Ergodyne Squids 3156 Coil Tool Lanyard with Single Carabiner
$7.79
|
Ergodyne Squids 3740 Hand Tool Attachment Trap - Slips (4-Pack)
$13.09
|
Description
Item#: ERGO-3194 Description
The Squids® Hand Tool Tethering Kit comes complete with a 3156 Coil Tool Lanyard featuring a Single Carabiner and a 3740 Hand Tool Attachment Trap – Slips™ Variety 4-Pack. This kit enables the secure tethering of four varying sizes of screwdrivers and hex key wrenches, ensuring easy tool usage on the job and preventing tool drops when working at elevated heights.
The 3156 Coil Tool Lanyard is more than just a small tool and hard hat lanyard. Built and tested to endure tough conditions and rated to support weight up to 2lbs / 0.9kg, the coiled lanyard is made with a low-profile design and durable plastic. With the lightweight aluminum carabiner on one end and a tethering loop on the other, it easily connects to tool anchors and attachments, even while wearing gloves. The coiled tether design reduces lanyard length to prevent snag and tangle hazards. The coil stretches from a compact 12in to 48in / 30cm to 122 cm.
STRAIGHTFORWARD INSTALLATIONNo additional install tools or complicated taping or shrinking! The patented Slips™ design requires a simple installation that follows its name. Simply “slip” the tool attachment on to the tool and connect the Squids® 3156 Coil Tool Lanyard to complete your tethering system. Unlike competitors that offer a fitted cap that can cover up information (like on the end of a screwdriver, for example) these solutions leave the end open. The single piece design is easier to install compared to competitors that require two to three pieces to be assembled onto the tool.
Simply poke the end of the hand tool through the orange interior membrane of the Tool Slip and slide the attachment to the desired location. The star points of the attachment’s interior will hold its location and the swiveling exterior ring will provide a connection point for tool lanyards. To remove the Slips™, simply push on the tab to loosen and then slide it off the shaft of the tool. No adhesive residue or mess will be left behind!
PERFECT FOR SMALL HAND TOOLSSmall hand tools have always been challenging to connect tool lanyards to. Screw drivers, small combination wrenches, punches, hex (Allen) wrenches and the like do not have captive connection points, and the low-profile designs can make it difficult for tapes, shrinks and tails to be applied. The Squids® Hand Tool Slips™ allow you to tether tools up to 1lb. based on their diameter. Four sizes of Slips™ are compatible on tools with diameters ranging from 0.05” (1.3mm) to ½” (12.5mm). Check out the size chart for specific ranges per size.
Ergodyne Squids 3194 Features:- Approved to the ANSI/ISEA 121-2018 standard
- Kit includes:
- One Variety 4-Pack 3740 Hand Tool Attachment Trap – Slips™
- Patent-pending one-piece design easily slides onto small hand tools without requiring additional tools to install or complicated wrapping or shrinking
- Swiveling exterior ring spins 360- degrees allowing screwdrivers and other rotating tools to be used without issue
- Flexible inner core grips tool after application securing it as an attachment point
- One 3156 Coil Low Profile Tool Lanyard with Single Carabiner
- Low-profile durable plastic coil to withstand even the toughest conditions
- Coiled lanyard design prevents snag and tangle hazards
- Lightweight aluminum carabiner with manual locking screw gate
- Tethering loop to securely connect to an anchor or tool attachment
- Coiled length 12in / 30cm; extended length 48in / 122cm
- Tether four different sized screwdrivers and hex key wrenches ranging from 0.05in - 0.5in // 1.3mm - 12.5mm diameter
- Maximum tethering capacity of up to 1lb / 0.5kg
Ergodyne is committed to customers' comfort, with work gear like ergonomic supports, work gloves, hats, safety vests, and more.
Item Reviews
- This item has not been reviewed.
- Be the first to review this item.
Returns & Exchanges
30 Day Return Policy
Our return policy gives you 30 days to return your products. This 30 day period begins on the date your order is delivered and includes both business and non-business days. Returned products must be in new, unused, and resalable condition. Customized products cannot be returned. If something is wrong with your order containing customized products, please contact us at 904-296-2240
To start a return, visit our Returns Center or learn more by reading our .
Shipping Information
Under normal circumstances, in stock orders placed by 12:00 PM EST are usually shipped out the following business day (Monday through Friday, excluding national holidays).
Due to a recent surge in online ordering across the country, most in stock orders are currently shipping out in 1-3 business days. Orders containing products that are not in stock can take longer to ship. Products that are not in stock have an estimated ship time located in the stock status section of the product page.
Find more shipping information or how to track your order in the Customer Center.
EAN/UPC
- 720476196648